Another WAP Push over SMS encoding

This entry is part 10 of 17 in the series Sending out an SMS

I still needed to show how you can send an Service Indication (SI) document like:

1
2
3
4
5
6
7
8
< ?xml version="1.0"?>
< !DOCTYPE si PUBLIC "-//WAPFORUM//DTD SI 1.0//EN"
                    "www.wapforum.org/DTD/si.dtd">
<si>
   <indication href="http://mobiletidings.com/"
     created="2009-02-26T16:25:00Z"
     si-expires="2009-03-04T16:25:00Z">Check out Mobile Tidings!</indication>
</si>

This document, a Service Indication, tells the WAP client to store the following:

  • A link to http://mobiletidings.com/
  • With text “Check out Mobile Tidings!
  • This typically shows up in a “WAP Push Inbox” or sometimes in the “SMS Inbox
  • The link will show when it was created
  • It should automatically be removed after the expiry time mentioned

Well here is the AT command to send this particular SI document:

Read More…

EMS and WAP Push support

This entry is part 9 of 17 in the series Sending out an SMS

As I have been writing about EMS and WAP Push, I am sure your ask yourself: “Does my phone support this?”. Again we dig into the WURFL database and we see that WAP Push is widely supported, but EMS a little less so.

This is understandable, because WAP Push is a protocol used in MMS (or picture messaging). Since most phones nowadays are camera phones and support picture messaging, they’re very likely to support WAP Push.

Here is a list of devices that support EMS and/or WAP Push, according to WURFL:

Read More…

WAP Push SMS encoding

This entry is part 8 of 17 in the series Sending out an SMS

As I started to explain in the last post, a WAP push consists of an XML document sent to the device over SMS. This is true but somewhat simplified.
The truth is that we send:

  • an WBXML encoded XML
  • over WSP (Wireless Session Protocol)
  • over WDP (Wireless Datagram Protocol)
  • over SMS

This is called an unconfirmed push.
Read More…

WAP Push over SMS

This entry is part 7 of 17 in the series Sending out an SMS

As you may understand, the data you can send via SMS is limited. It is limited because:

  • A single message can only hold 160 GSM-7 encoded characters
  • Even though messages can be combined in to bigger ones, the total size is still limited in several ways:
    • A message can have at most 256 parts
    • The receiving device as a (much lower) limit on how many parts it can reassemble into a bigger message
  • And if the technical limits aren’t prohibitive, the cost might be

So how do you send more and richer information to a device? There are 2 possibilities:

  • WAP push
  • MMS

Today I’ll focus on WAP push.

Read More…

Combining SMS messages

This entry is part 6 of 17 in the series Sending out an SMS

As discussed in a previous post, many features of SMS messages become available if you can set the User Data Header (UDH) field.

When using a GSM modem in text mode you can’t sent a UDH, so you need to use PDU mode.

How do you add a UDH?

There are 2 things you need to do:

  • Set the UDH bit in the first octet of the PDU. For an SMS-SUBMIT PDU (the only one we’ve been using so far) the value is normally 0×01. To indicate that a UDH is present we need to set bit 6 (0×40). So for an SMS-SUBMIT with UDH present we set the PDU type to 0×41.
  • With the UDH bit set, this first octet of the payload (or User Data = UD) needs to indicate the length of the UDH in octets. This field is known as UDHL.

Read More…

What are EMS messages?

This entry is part 5 of 17 in the series Sending out an SMS

EMS stands for Enhance Message Services. EMS messages are just SMS messages with a twist.

EMS messages make use of the User Data Header to add some meta data to the SMS message being sent. This meta data is separate from the actual text and devices that don’t understand some or any of the EMS features will easily skip over them and just render the text.

The uses of EMS are many:

Read More…

Sending a flash SMS message

This entry is part 4 of 17 in the series Sending out an SMS

So far I’ve show how to send a text message in PDU mode. There is nothing special about this. There are a number of things you can do in PDU mode, that you can’t do in text mode.

A first example is a flash SMS message.

A flash SMS message is an SMS message that, instead of being stored in the SIM or memory of the receiving phone, pops-up on the receiving phone’s screen, without the user taking any action. When dismissed the message is usually gone.

Here is an example AT command to send a flash SMS message in PDU mode:

AT+CMGS=28<crlf>
> 0001010B915121551532F40010104190991D9EA341EDF27C1E3E9743<Ctrl-Z>
Here is what the individual octets represent:

Read More…

More on the SMS PDU

This entry is part 3 of 17 in the series Sending out an SMS

As discussed in an earlier post, you can connect to a GSM modem and use AT commands to send SMS messages. There are 2 possible methods: text mode and PDU mode.

It turns out that most devices support PDU mode, but only a few support text mode.

Here is an example AT command to submit a PDU:

AT+CMGS=24<crlf>
> 0001000B915121551532F400000CC8F79D9C07E54F61363B04<Ctrl-Z>
As explained before the size (24) is the number of octets in the PDU. he PDU itself is passed as a hex representation of those octets (48 characters). Here is what the individual octets represent:

Read More…

Dramatic effects of a layout change

A few days back I initially posted the article ‘Collected UAProf URLs’. The format I used for the information was one big table with the first column the brand, the second column the model and the third column the UAProf URLs, e.g.:

Asus 1210 http://uaprofile.asus.com/uaprof/ASUS121…
  ASUS-P550 http://uaprofile.asus.com/uaprof/ASUS-P5…
  GalaxyII http://uaprofile.asus.com/uaprof/ASUS-Ga…
  GalaxyMini http://uaprofile.asus.com/uaprof/ASUS-Ga…
  J501 http://uaprofile.asus.com/uaprof/ASUS-J5…

Read More…