WAP Push SMS encoding

This entry is part 8 of 17 in the series Sending out an SMS

As I started to explain in the last post, a WAP push consists of an XML document sent to the device over SMS. This is true but somewhat simplified.
The truth is that we send:

  • an WBXML encoded XML
  • over WSP (Wireless Session Protocol)
  • over WDP (Wireless Datagram Protocol)
  • over SMS

This is called an unconfirmed push.
Read More…

WAP Push over SMS

This entry is part 7 of 17 in the series Sending out an SMS

As you may understand, the data you can send via SMS is limited. It is limited because:

  • A single message can only hold 160 GSM-7 encoded characters
  • Even though messages can be combined in to bigger ones, the total size is still limited in several ways:
    • A message can have at most 256 parts
    • The receiving device as a (much lower) limit on how many parts it can reassemble into a bigger message
  • And if the technical limits aren’t prohibitive, the cost might be

So how do you send more and richer information to a device? There are 2 possibilities:

  • WAP push
  • MMS

Today I’ll focus on WAP push.

Read More…

Combining SMS messages

This entry is part 6 of 17 in the series Sending out an SMS

As discussed in a previous post, many features of SMS messages become available if you can set the User Data Header (UDH) field.

When using a GSM modem in text mode you can’t sent a UDH, so you need to use PDU mode.

How do you add a UDH?

There are 2 things you need to do:

  • Set the UDH bit in the first octet of the PDU. For an SMS-SUBMIT PDU (the only one we’ve been using so far) the value is normally 0×01. To indicate that a UDH is present we need to set bit 6 (0×40). So for an SMS-SUBMIT with UDH present we set the PDU type to 0×41.
  • With the UDH bit set, this first octet of the payload (or User Data = UD) needs to indicate the length of the UDH in octets. This field is known as UDHL.

Read More…

What are EMS messages?

This entry is part 5 of 17 in the series Sending out an SMS

EMS stands for Enhance Message Services. EMS messages are just SMS messages with a twist.

EMS messages make use of the User Data Header to add some meta data to the SMS message being sent. This meta data is separate from the actual text and devices that don’t understand some or any of the EMS features will easily skip over them and just render the text.

The uses of EMS are many:

Read More…

Sending a flash SMS message

This entry is part 4 of 17 in the series Sending out an SMS

So far I’ve show how to send a text message in PDU mode. There is nothing special about this. There are a number of things you can do in PDU mode, that you can’t do in text mode.

A first example is a flash SMS message.

A flash SMS message is an SMS message that, instead of being stored in the SIM or memory of the receiving phone, pops-up on the receiving phone’s screen, without the user taking any action. When dismissed the message is usually gone.

Here is an example AT command to send a flash SMS message in PDU mode:

AT+CMGS=28<crlf>
> 0001010B915121551532F40010104190991D9EA341EDF27C1E3E9743<Ctrl-Z>
Here is what the individual octets represent:

Read More…

More on the SMS PDU

This entry is part 3 of 17 in the series Sending out an SMS

As discussed in an earlier post, you can connect to a GSM modem and use AT commands to send SMS messages. There are 2 possible methods: text mode and PDU mode.

It turns out that most devices support PDU mode, but only a few support text mode.

Here is an example AT command to submit a PDU:

AT+CMGS=24<crlf>
> 0001000B915121551532F400000CC8F79D9C07E54F61363B04<Ctrl-Z>
As explained before the size (24) is the number of octets in the PDU. he PDU itself is passed as a hex representation of those octets (48 characters). Here is what the individual octets represent:

Read More…

Sending out an SMS in PDU mode

This entry is part 1 of 17 in the series Sending out an SMS

PDU mode is a lot more interesting than text mode. There are all kinds of things that can be done with SMS messages, all leveraging special formatting that is only available if you use PDU mode:

The formatting of these PDU’s is a little more complicated and requires some bit manipulations that are hard to do by hand.

The GSM modem is put into PDU mode with the command ‘AT+CMGF=0’. Once in PDU mode a PDU can be sent using the ‘AT+CMGS’ command:
Read More…

Sending out an SMS in text mode

This entry is part 1 of 17 in the series Sending out an SMS

As explained in a prevous post in this series, a GSM modem can let you send SMS messages from a PC. There are two basic ways to do this: text mode and PDU mode.

You can play around with your GSM modem using a terminal program like HyperTerminal (which came with Windows XP, but is no longer there in Windows Vista). The commands I mention can just be entered in the terminal window when connected to the modem. You can try the following basic commands, any modem should support these:

ATI Returns general modem identification
ATD<phone number> Dials the phone number you supplied (don’t enter the <> brackets)
ATH Hang-up the phone (useful after the previous command).

The following commands are specific for GSM modems. If you get an error response (e.g. ‘+ERR’), your modem probably isn’t a GSM modem or it doesn’t support the extensions specific for GSM modems. Read More…

Send an SMS from your PC

Sending an SMS from a PC to a GSM phone can be done in many ways.

The first method I discuss requires a GSM phone attached to your PC.

The GSM phone (or GMS card) can be connected to your PC in different ways; using BlueTooth, infrared (IrDA) or a serial cable. The way the phone is connected is irrelevant, what counts is that the GSM is available as a modem. On windows PCs this means that it will be available as a TAPI modem.

Programs make modems do things by sending them so called AT commands. E.g.

ATD5551234 makes the modem dial a connection to the number 5551234.

ATA makes the modem answer an incoming call. All your modem’s features are available using commands like these.

Read More…